Welcome To Roberts Warr Electronics Limited

Hitron Power Supply Distributor for the UK

Latest Products

H HiTRON

UNIVERSAL AC INPUT HARMONIC CORRECTION AC-DC HOT-SWAP
CompactPCI QUAD OUTPUT 175 WATTS CURRENT SHARING
SWITCHING POWER SUPPLIES HAC175P & HAC175D SERIES

SPECIFICATION

FEATURES:

  • 175W IN 3U X 8HP EUROCARD PACKAGE
  • UNIVERSAL AC INPUT WITH PFC
  • INTERNAL OR-ING DIODES FOR N+1 REDUNDANCY
  • HOT-SWAPPABLE
  • DROOP CURRENT SHARING
  • EMI MEET EN 55022 / FCC CLASS A
  • CE MARKING COMPLIANCE
  • FULLY COMPLIANT WITH PICMG
OUTPUT SPECIFICATION
Output Voltage: See Ratings Chart.
Output Current: See Ratings Chart.
Output Wattage: Typ. 175W continuous.
Output Connector: PCIH47M400A1 for HAC175P. DIN41612 M24/8 for HAC175D.
Line Regulation: Typ. 0.5%.
Load Regulation: VO1 & VO2 typ. ±1.0%. VO3 & VO4 typ. ±2.0%.
Noise & Ripple: Typ. 1% peak-peak or 50mV, whichever is greater.
OVP: Built-in at VO1 & VO2.
Adjustability: Available at VO1 & VO2. VO3 factory set.
Remote Sensing: Available at VO1 & VO2.
Hot-Swap: Available.
N+1 Redundancy: Installed with OR-ing diodes for N+1 redundancy operation.
Current Sharing: Droop current sharing at all output.
Power OK Signal: Available for VO1 & VO2.
Over Current Protection (OCP): Installed in all outputs.
Overload Protection (OLP): Fully protected against output overload and short circuit. Consult factory for special OLP setting.
INPUT SPECIFICATION
Input Voltage: Typ. 90-264Vac with PFC.
Power Factor Correction: Meet Harmonic Correction IEC 61000-3-2. Power Factor typ. 0.98
Input Connector: PCIH47M400A1 for HAC175P. DIN41612 M24/8 for HAC175D.
Input Frequency: 47-63Hz.
Inrush Current: < 30A @ 230Vac by adding thermistor
Input Current: 2.2A @115Vac/1.1A @230Vac for HAC175D. 2.4A @115Vac/1.2A @230Vac for HAC175P
Dielectric Withstand: Meet IEC 60950-1 regulation.
EMI: Meet EN 55022 / FCC Class A.
Hold-up Time: 5mS @115V & 230Vac after power fail signal.
Remote ON/OFF: Available at [INH#] & [EN#] pins.
Power Fail Signal: Available at [FAL#] pin.
Status LED:
means valid input voltage. means a critical fault.
Thermal Protection: Installed NTC for thermal sensor at [DEG#] pin.
Earth Leakage: Less than 0.5mA @230Vac.
GENERAL SPECIFICATION
Efficiency: Typ. 75-78%.
Switching Frequency: 100 KHz.
Circuit Topology: Half-bridge circuit.
Transient Response: Typ. 1.0mS for a 25% load change.
Safety Standard: IEC 60950-1/UL 60950-1 Class I.
Construction: Eurocard 3U x 8HP x 160mm
CompactPCI format. Front Panel with either
Ordinary handle or Extractor handle.
Operating Temperature: 0 to +50°C at full load with specified air flow.
Derates linearly to 50% at +70°C.
Storage Temperature: -40°C to +85°C.
Temperature Coefficient: Typ. ±0.02% /°C.
Cooling: At least 20cfm (600lfm) airflow is required to deliver full rating load.
Power Density: 3.2 Watts /Cubic Inch.

NOTE:
Due to requests in market and advances in technology, specifications subject to change without notification.

OUTPUT VOLTAGE / CURRENT RATINGS CHART

QUAD OUTPUT

MODEL NO.
MAIN +VO1 @"#=*
AUX. +VO2 ▲@"#=*
AUX. +VO3 (@)▲=*
AUX. +VO4 =*●
Min. Typ. Volt. Max.
Typ. Volt. Max.
Typ. Volt. Max. Peak
Typ. Volt. Max. Peak
HAC175P-490(E)
0.0A 20A +5V 35A
10A +3.3V 20A
3.0A +12V # 5.0A 6A
0.5A -12V 1.0A 1.0A
HAC175P-490(O)
0.0A 20A +5V 35A
10A +3.3V 20A
3.0A +12V # 5.0A 6A
0.5A -12V 1.0A 1.0A
HAC175D-490(O)
0.0A 20A +5V 35A
10A +3.3V 20A
3.0A +12V 5.0A 6A
0.5A -12V 1.0A 1.0A

Symbol: """ OVP built-in. "@" Adjustable. "(@)" Adjustable factory set.. "#" Remote sensing. "=" Droop Load Sharing. "*" Installed with Or-ing diode.
"▲" Magnetic Amplifier. "●" Installed with Post Regulator.
Remark: Peak load less than 60sec. with duty cycle <10%.
Max. load is the continuous operating load of each rail. But the max. load of each rail can't be drawn from all outputs at the same time.

MECHANICAL DIMENSIONS: MM [INCHES] WEIGHT: 666.0g (23.5 Oz.)

HPG90 mechanical dimensions

 

INPUT & OUTPUT CONNECTORS PIN ASSIGNMENT

ASSIGNMENTPIN NO.
AC-L47
AC-N46
AC-GND45
VO11,2,3,4.
VO1 S +30
VO1 S -34
VO213, 14, 15, 16, 17, 18.
VO233
VO3 S+20
VO3 S+36
VO421
DC COM5, 6, 7, 8, 9, 10, 11, 12, 19 ,24.
EN#27
DEG #38
INH #39
FAL #42
Mating connector: PCIH47F400A1

INPUT & OUTPUT CONNECTORS PIN ASSIGNMENT

ASSIGNMENTPIN NO.
AC-LB2
AC-NB5
AC-GNDB11
VO1B22
VO1 S +A17
VO1 S -A16
VO2B13,14,15,16,17,18.
VO2 S+A18
VO3B19
VO4B20
DC COMB25
EN#C13
DEG #C14
INH #A14
FAL # C15
Mating connector: DIN 41612 M24/8-F